manualshive.com logo in svg

Dataradio Integra-TR, Technical Manual, Page: 55 / 68

Share
Download
Dataradio Integra-TR Technical Manual Download Page 55

4-3

Part No. 001-4008-101/102

4.4  OFFLINE LINK TEST

Tests the network data link status by sending a number of transmissions to a remote unit, back from the 
remote, computing a ratio of good to bad signals received and displaying the result as a link quality for both 
individual links as well as the overall link.

Caution: Shut down your application before pressing “Link Test”.

Before starting a Link Test:

1. Ensure that the Radio Source selected is “Remote”. 
2. Click in the active Short ID field and enter the address of the desired remote unit.
3.  Press the “Link Test” button to start transmitting blocks of data. 

The selected remote decodes and returns data blocks. Transmission will continue until the link test button is 
pressed again or after 100 data blocks are transmitted. The sent and received data are compared and the ratio 
of good to bad blocks are calculated. The error rate is calculated separately for each direction and for the 
link as a whole. The results are displayed on the message screen in the format detailed in Table 4-2.

 Temp

 Internal case temperature

 Operating limits:
   -30 degrees C    to
   +75 degrees C

SWB+

 Selected unit main DC power measured in tenths of a volt 
from 6.0 to 18.8 volts, 

WARNING: Do not exceed 16Vdc

.

Application of more than 16 VDC will damage the unit and is 
not covered by the warranty.

 Should nominally be close to 
13.3VDC

Operating limits:

10.0 to 16.0 V

Peak

Demodulated signal voltage: peak-to-peak
(Available only for Offline Get Stats)

See transmit deviation tables

Ext1

   User-specified “Analog 1" input as a voltage be-tween 0 and 

10 volts DC in tenths, at 8 bits of resolution.
(Available only for Offline Get Stats)
If the “Fan Control” (Analog 1) box is checked in the RSS 
program, the value displayed will be 00.0 Volt

 

 0 to 10.0 VDC

Ext2

User-specified “Analog 2" input as a voltage be-tween 0 and 
10 volts DC in tenths, at 8 bits of resolution.
(Available only for Offline Get Stats)
If the “Rx/Tp (Analog 2) box is checked in the RSS program, 
the value displayed will be 00.0 Volt

 0 to 10.0 VDC

Good

 Number of correctly decoded transmissions in the last 15 
received
In multiple frequency networks (duplex), this ratio will be an 
aggregate of all stations heard. In single frequency networks 
(simplex), this ratio usually represents receptions from the 
master station.

15/15 equals 100% Lower 
values (8/15), coupled with 
strong received signals 
(Remote RSSI), usually mean 
local interference at the 
remote site.

Total

Used with the number in the field “Good” to establish a 
percentage indicative of reception quality.

Field Name

Description

Tolerance

Summary of Contents for Integra-TR





































































Reviews:

No comments