manualshive.com logo in svg

Dataradio Integra-TR, Technical Manual, Page: 3 / 68

Share
Download
Dataradio Integra-TR Technical Manual Download Page 3

SECTION 1

PRODUCT OVERVIEW

1-1

001-4008-101/102

1.1 SCOPE OF MANUAL

This document provides the information required for the operation and preventive maintenance of the 
D

ATARADIO

 Integra-TR wireless modem. This manual is intended for system designers, installers and 

maintenance technicians

1.2  GENERAL DESCRIPTION

 Integra-TR is a high-speed transparent wireless modem. It is FCC refarming compliant and designed 
specifically to fit the needs of SCADA, telemetry and control applications. Integra-TR provides the 
communication links to data equipment for installations where wired communication is impractical.

Integra-TR works with most makes and models of remote terminal units (RTU) and programmable logic 
controllers (PLC) and their protocols. Configuration settings allow tailoring for a variety of applications.

Integra-TR supports:

1. Point to point Master-Remote or Peer-to-Peer configurations in simplex or half-duplex modes.

2. Point to multipoint Master-Remote configuration in simplex or half-duplex modes and offers full-duplex in 

dual-unit configuration.

Settings and connections for these configurations are given later in this manual

1.2.1  CHARACTERISTICS

 Integra-TR has the following characteristics:

z

 Selectable network speeds of 4800 and 9600 b/s for half channel units as well as 4800, 9600 and 19.200     
b/s for full channel units. 2400 or 4800 b/s for quarter channel units

z

 Backward compatible with the Integra-T for bit rate of 4800 and 9600 b/s (full channel units only)

z

 One COM port for connection to DTE. Speed of 300 - 19200 bauds

z

 One Setup port, for configuration and diagnostics (speed fixed to 9600 baud, 8 bit, no parity, 1 stop bit)

z

 Built-in 5-watt transceiver, operating in the VHF, UHF or 900 MHz communications bands. Half-duplex or 
simplex operation

z

 Fully transparent operation with error-free data delivery

z

 Allows transmission of “break” characters

z

 DOX (Data Operated Transmit) or RTS mode

z

 Stations may be set as “master” or “remote” to prevent remote stations from hearing each other in a simplex 
RF configuration

z

 Full local and remote diagnostics

z

 Two 8-bit analog inputs (0 - 10V)

z

 Low power consumption modes: “sleep” and “suspend” modes (< 20 mA).

z

 “12 VDC, negative ground” device.

Summary of Contents for Integra-TR





































































Reviews:

No comments