manualshive.com logo in svg

Dataradio Integra-TR, Technical Manual, Page: 40 / 68

Share
Download
Dataradio Integra-TR Technical Manual Download Page 40

2-20

Part No. 001-4008-101/102

Figure 2-18   Offline Diagnostics Screen

Diagnostic Select / Selected Remote ID

This button allows the user to gather Offline Diagnostics from the selected Remote ID only.

Diagnostic Select / Remote ID List

This button allows the user to gather Offline Diagnostics from all the IDs in the list of Remote IDs 
(including the local unit).

Get Diags

The Get Diags button allows the user to send the command for Offline Diagnostics. The command is sent to 
the unit connected to the computer if the Local ID button is selected. The command is sent to the selected 
Remote ID if the Remote ID and Selected Remote ID buttons are selected. The command is sent to the list 
of Remote IDs if the Remote ID and Remote ID List buttons are selected.

Stop

The Stop button allows the user to stop any commands for Offline Diagnostics from being sent.

Save

The Save button allows the user to save the current Offline Diagnostics to a file.

RSSI/Pwr

The RSSI/Pwr panel shows the current RSSI level (in dBm) while the local unit is receiving and the current 
Power Level (in watts) while the local unit is transmitting.

Rev Pwr

Summary of Contents for Integra-TR





































































Reviews:

No comments