manualshive.com logo in svg

Datalogic ENC-58 PROG, Instruction Manual, Page: 34 / 38

Share
Download
Datalogic ENC-58 PROG Instruction Manual Download Page 34

 

ENC58  PROG

 

 

 

 

29 

 

5.5 Error messages 

 
(in alphabetical order) 
 

Activation error of sensor data!!!!! 

The operator has pressed the READ button but an error has 
occurred while processing the information (it is signalled through the 
LED lit red in the diagnostic information section of the page). 
Please close the programming interface, then turn off and on the 
power supply of the encoder (disconnect and connect again the USB 
cable), finally restart the programming interface. 
 
 

Beware!!! Displayed parameters could differ from encoder 
parameters!! 

The operator has pressed the Load config button (or otherwise as an 
alternative the Load config command in the File menu) in order to 
upload a previously saved encoder configuration.  
After having select and confirmed the .cfg or .hex file to upload, the 

Would you like to update also encoder parameters?

 message 

appears on the screen after a few seconds. 
If you choose  YES, the configuration parameters are updated in 
both the programming interface and the encoder; otherwise, if you 
press NO, the configuration parameters are updated only in the 
programming interface, they are not downloaded to the encoder. 
In the 

Messages

 section below in the page the 

Beware!!! Displayed 

parameters could differ from encoder parameters!!

 message warns of 

occurrence and the Load config button starts blinking red. 
 

Beware!!! Voltage output will be changed!!! Continue? 

The operator is going to change the voltage level at the output 
channels by programming the 

Voltage output

 parameter. 

This message is intended to ask the operator to confirm before 
proceeding. 
 
 

Device not connected!!!!! Click on 'Disconnected' button 

If you try to send a command while the encoder is not connected yet, 
then the 

Device not connected!!!!! Click on 'Disconnected' button

 

warning message will appear on the screen. 
Press the DISCONNECTED button to activate the communication 
and start programming the encoder. 
 
 

Encoder disconnected!!! Check encoder connections 

This warning message is triggered when the interface establishes a 
proper USB connection, but it is not able to communicate with the 
encoder. 
When this happens, please check either the M23 connector. 
 

Summary of Contents for ENC-58 PROG







































Reviews:

No comments