manualshive.com logo in svg

Datalogic ENC-58 PROG, Instruction Manual, Page: 24 / 38

Share
Download
Datalogic ENC-58 PROG Instruction Manual Download Page 24

 

ENC58  PROG

 

 

 

 

19 

 
If the encoder is not connected properly and the software tool is not 
able to establish a USB connection, then the USB to I2C not found: 
check connections!!! warning message appears on the screen. 
In such occurrence please check that the USB cable is connected 
properly to the USB port and the USB port is working correctly. 
 

 

 
It may happen that the interface establishes a proper USB 
connection, but it is not able to communicate with the encoder. 
In this case the following warning messages appear one after the 
other: Reading error of parameters from encoder!!! 
Connect again (Disconnected button) and Encoder disconnected!!! 
Check encoder connections. When this happens, please check either 
the M23 / M12 connectors or the cable wiring in the terminal. 
 

 

 

 

 

If the software tool is able to connect to the encoder and 
communicate properly, but internal errors or faults are found, they will 
be indicated by their LEDs lighting red in the diagnostic section of the 
page. 
Errors are also shown by means of the LEDs in the enclosure of the 
encoder; please refer to the section “4.10 Diagnostic LEDs (Figure 
1)” on page 11. 
 

 

Summary of Contents for ENC-58 PROG







































Reviews:

No comments