manualshive.com logo in svg

Datalogic ENC-58 PROG, Instruction Manual, Page: 19 / 38

Share
Download
Datalogic ENC-58 PROG Instruction Manual Download Page 19

ENC58  PROG 

 

 

14 

 
WARNING 
Please make sure that only one encoder is connected to the KIT 
ENC58 when you activate the USB connection ! 
 
 
NOTE 
Before configuring the encoder by means of the programming 
interface, you must connect it to the personal computer through the 
KIT ENC58 connection cable. You are required to install the drivers 
of the USB Serial Converter and the USB Serial Port first.  
The drivers are available for download at the following address 
www.datalogic.com. 
 

4.12.1 Installing the KIT ENC58 USB drivers 
 
Please follow the steps in the documents listed below to install the 
drivers of both the USB Serial Converter and the USB Serial Port of 
the KIT ENC58. 
The drivers package and the relevant documents are found inside 
the EXC_USB4_driver folder. As stated, the drivers are available for 
download at the following address www.datalogic.com. 
If you need to install the drivers under the Microsoft Windows XP 
operating system, please refer to the following document: 
Installation_Guide_for_WindowsXP.pdf. 
If you need to install the drivers under the Microsoft Windows Vista 
operating system, please refer to the following document: 
Installation_Guide_for_VISTA.pdf. 
If you need to install the drivers under the Microsoft Windows 7 
operating system, please refer to the following document: 
Installation_Guide_for_Windows7.pdf. 
 
As a preliminary operation please: 
1. connect the KIT ENC58 cable to the encoder through the M23 12-

pin connector or the M12 12-pin connector or the provided 
terminal (for the cable connection scheme please refer to the table 
in the previous page); you do not need to power the encoder by 
means of an external power pack as the device gets the power 
from USB; 

2. connect the cable fitted with the USB connector to a USB port of 

your PC; after a few seconds a message will appear in the 
notification area of the Windows taskbar and the USB Serial 
Converter drivers installation wizard will start. Then follow the 
instructions in the above mentioned pdf documents. 

 
After installation you can launch the executable file and open the 
encoder programming interface; to know more refer to the section 
“Programming interface” on page 15. 
 

 

Summary of Contents for ENC-58 PROG







































Reviews:

No comments