Datakom D-100 MK2 User Manual Download Page 65 | Manualshive

Page: 65 / 123

background image

D-100 MK2 User Manual Firmware V-6.3

K96D01-EN - 65 -

Parameter Definition

Unit

Min

Max

Factory

Set

Description

001-LCD Contrast

-

30

50

31

This parameter is used to set LCD
contrast. Adjust for the best viewing
angle.

002-Fault Holdoff Timer

sec

0

120

12

This parameter defines the delay after
the engine runs and before the fault
monitoring is enabled.

003-Alarm Relay Timer

sec

0

120

60

This is the period during which the
ALARM relay is active. If the period is
set to 0, this will mean that the period is
unlimited.

004-Emergency Backup
Operation

-

0

1

0

0: In RUN mode, the load will not be
transferred to the genset even if the
mains fails.
1: In RUN mode, the load will be
transferred to the genset if the mains
fails.

005-Exercise Time

-

006-Exercise Period

-

0

1

0

0: exercise once per week
1: exercise once per month
The exact exerciser day and time is
adjusted within the EXERCISE
SCHEDULE section.

007-Exercise Off/On
Load

-

0

1

1

0: Exercise at RUN mode
1: Exercise at TEST mode

008-Delayed Simulate
Mains

-

0

1

0

0: delayed simulate mains disabled
1: delayed simulate mains enabled

009-SMS Enable

-

0

1

0

0: SMS messages disabled
1: SMS messages enabled

010-GPRS Connection
Enable

-

0

1

0

0: GPRS disabled
1: GPRS enabled

011-Rainbow Scada
Refresh Rate

sec

0

65535

5

The unit will update the distant
monitoring terminal with this rate.

012-Rainbow Scada
Address-1 Port

-

0

65535

0

This is the port number of the first
monitoring terminal address.

013-Rainbow Scada
Address-2 Port

-

0

65535

0

This is the port number of the second
monitoring terminal address.

014-Modbus Address

-

0

240

1

This is the modbus controller identity
used in Modbus communication.

015-Oil Pressure Switch
Priority

-

0

1

0

0: crank cut is performed through oil
pressure switch and oil pressure sender
reading
1: crank cut is performed only through
oil pressure switch

016-Flashing Relay ON
Timer

min

0

1200

0

Delayed Simulate Mains Operation:
max genset running time after Simulate
Mains signal disappears.
Dual Genset Systems: flashing relay
ON state duration timer.

017-Flashing Relay OFF
Timer

min

0

1200

0

Dual Genset Systems: flashing relay
OFF state duration.

16. PROGRAM PARAMETER LIST

«
...
63
64
65
66
67
...
»

Summary of Contents for D-100 MK2




























































































































Reviews:

No comments

Related manuals for D-100 MK2

Brand: Banner Pages: 15

Brand: bar Pages: 2

Brand: Hama Pages: 8

Brand: Hama Pages: 7

Brand: Hama Pages: 44

Brand: RadioMaster Pages: 10

Brand: K&K Pages: 6

Brand: Samson Pages: 2

ecomat 100 R 360

Brand: IFM Electronic Pages: 16

Ecomot300 AC2630

Brand: IFM Electronic Pages: 11

Brand: IFM Electronic Pages: 23

Brand: Oceanic Systems Pages: 8

Brand: Parkside Pages: 86

Brand: Radware Pages: 98

Brand: RabbitCore Pages: 34

Brand: R82 Pages: 11

Brand: Nice Pages: 32

Brand: BEBE CONFORT Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands