Datakom D-100 MK2 User Manual Download Page 52

Page: 52 / 123

D-100 MK2 User Manual Firmware V-6.3

K96D01-EN - 52 -

STOPPING THE ENGINE:

Press STOP

button

STARTING THE ENGINE:

Press RUN

button

LOAD TEST:

Hold pressed RUN

button for 5 seconds. The genset will run and take the load.

AUTOMATIC OPERATION:

Press AUTO

button. Check that

AUTO READY

led is illuminated.

The STOP mode is entered by pressing the

button.

In this mode, the genset will be in a rest state.

When STOP mode is selected, if the genset is running under load, then it will be immediately unloaded. The
engine will continue to run during

Cooldown Timer

and will stop afterwards.

If the STOP button is pressed again, then the engine will immediately stop.

If the engine fails to stop after the expiration of

Stop Timer

then a

Fail to Stop

warning will occur.

In this mode, the mains contactor will be energized only if mains phase voltages and frequency are within the
programmed limits. If enabled, the mains phase order is also checked.

If a

Remote Start

Force to Start

signal arrives in STOP mode, the genset will not start until AUTO mode

is selected.

Mode can be changed anytime without negative effect.

Changing the operation mode while the genset is running will
result into a behavior suitable for the new operating mode.

13.2. STOP MODE

13.1. QUICK START GUIDE

13. OPERATION OF THE UNIT

Summary of Contents for D-100 MK2




























































































































Search results

Summary of Contents for D-100 MK2

Reviews:

Related manuals for D-100 MK2

Brands by name

Popular brands

Datakom D-100 MK2, User Manual

Search results

Summary of Contents for D-100 MK2

Reviews:

Related manuals for D-100 MK2

Brands by name

Popular brands