Datakom D-100 MK2 User Manual Download Page 24

Page: 24 / 123

D-100 MK2 User Manual Firmware V-6.3

K96D01-EN - 24 -

Structure:

CANBUS, non isolated.

Connection:

3 wires (CANH-CANL-GND).

Data rate:

250 kbps

Termination:

Internal 120 ohms provided

Common mode voltage:

-0.5 VDC to +15 VDC, internally clamped by transient suppressors.

Max distance:

200m with 120 ohm balanced cable

Description:

USB 2.0, not isolated, HID mode

Data rate:

Full Speed 1.5/12 Mbits/s, auto detecting

Connector:

USB-B (printer connector)

Cable length:

Max 6m

Functionality:

Modbus, FAT32 for firmware upgrade (boot loader mode only)

The USB-Device port is designed to connect the module to a PC. Using the RainbowPlus software,
programming, control of the genset and monitoring of measured parameters are achieved.

The RainbowPlus software can be downloaded from

www.datakom.com.tr

website.

The connector on the module is of USB-B type. Thus A to B type USB cable should be used. This is the
same cable used for USB printers.

For more details about programming, control and monitoring please refer to RainbowPlus user manual.

The battery voltage must be connected.

3.14. USB DEVICE PORT

3.13. J1939-CANBUS PORT

USB A to B
Cable

USB Device
Connector

Summary of Contents for D-100 MK2




























































































































Search results

Summary of Contents for D-100 MK2

Reviews:

Related manuals for D-100 MK2

Brands by name

Popular brands

Datakom D-100 MK2, User Manual

Search results

Summary of Contents for D-100 MK2

Reviews:

Related manuals for D-100 MK2

Brands by name

Popular brands