Datacom Systems VS-1200-S Series User Manual Download Page 29

Page: 29 / 90

Initial Configuration

4.1.4.16 SET UPGRADE (SE UP)

This command sets the FLASHutils service (default ENABLED) process. It is entered as shown:

SET UPDATE (SE UP) [OFF or ON]

Example 1:

# SE UP OFF
The FlashUtils protocol is now disabled.
#

Example 2:

# SE UP ON
The FlashUtils protocol is now enabled.
#

4.1.4.17 SET TELNET (SE TT)

This command sets the TELNET service (default ENABLED) process. It is entered as shown:

SET TELNET (SE TT) [OFF or ON]

Example 1:

# SE TT OFF
The Telnet protocol will be disabled at end of session.
#

Example 2:

# SE TT ON
The Telnet protocol will be enabled at end of session.
#

4.1.4.18 SET SSH (SE SH)

This command sets the SSH service (default ENABLED) process. It is entered as shown:

SET SSH (SE SH) [OFF or ON]

Example 1:

# SE SH OFF
The SSH protocol will be disabled at end of session.
#

Example 2:

> SE SH ON
The SSH protocol will be enabled at end of session.
#

Summary of Contents for VS-1200-S Series



























































































Search results

Summary of Contents for VS-1200-S Series

Reviews:

Related manuals for VS-1200-S Series

Brands by name

Popular brands

Datacom Systems VS-1200-S Series, User Manual

Search results

Summary of Contents for VS-1200-S Series

Reviews:

Related manuals for VS-1200-S Series

Brands by name

Popular brands