Datacom Systems VS-1200-S Series User Manual Download Page 63 | Manualshive

Page: 63 / 90

background image

Appendix A - Agent Capabilities MIB

63

© 2011 Datacom Systems Inc

9

Appendix A - Agent Capabilities MIB

The Datacom Agent Capabilities MIB

This Appendix specifies a proprietary MIB module of Datacom Systems Inc.

Distribution of this memo is limited to Datacom product licensees
and other interested parties having express written consent from
Datacom Systems Inc.

The current set of Datacom Enterprise MIB modules may be requested
by sending an email to [email protected].

Copyright Notice

Copyright (C) 2010 Datacom Systems Inc. All Rights Reserved; use is
subject to license terms.

Abstract

This memo defines a set of agent identities used to identify Datacom
SNMP agents and a set of agent capabilities used to convey the
capabilities of Datacom SNMP Agents.

Table of Contents

1. Introduction
2. The Internet-Standard SNMP Management Framework
3. Conventions
4. Overview of the Datacom Agent Capabilities MIB Module
4.1 Agent Identities
4.2 AGENT-CAPABILITIES statements
5. Definitions
6. Acknowledgments
7. Security Considerations
8. References
8.1 Normative References
8.2 Informative References
9. Change Log

«
...
61
62
63
64
65
...
»

Summary of Contents for VS-1200-S Series



























































































Reviews:

No comments

Related manuals for VS-1200-S Series

Brand: CALIENT Pages: 22

Brand: Campbell Pages: 14

Brand: Sams Pages: 10

Brand: ATEN Pages: 2

Brand: Homefibre Pages: 2

Smart Switch 2:1

Brand: XTBA Pages: 3

Brand: CYP Pages: 28

3CB9E7 - CoreBuilder 9000 Chassis Switch

Brand: 3Com Pages: 132

MultiView CE-H26311-S1

Brand: SIIG Pages: 24

Brand: A-Neuvideo Pages: 15

PICO-GUARD SFI-D1EDPXT6

Brand: Banner Pages: 2

Brand: Linkskey Pages: 2

EXT-HDMI-CAT5-844

Brand: Gefen Pages: 28

Brand: Net Optics Pages: 20

D-PFS4226-24ET-240

Brand: Dahua Pages: 16

Brand: H3C Pages: 19

Brand: N-Tron Pages: 169

ICS5400PTP-12GT12GS4XS

Brand: 3onedata Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands