manualshive.com logo in svg

Datacom Systems VS-1200-S Series, User Manual

Share
Download
Datacom Systems VS-1200-S Series User Manual Download Page 19

Initial Configuration

19

© 2011 Datacom Systems Inc

4

Initial Configuration

IMPORTANT: 

Prior to initial configuration of the hardware, it is imperative to review the

entire Initial Configuration section before proceeding to the Installation section.

This section explains the considerations and requirements for the initial configuration of the VS-
1200-S series by a Command Line Interface (CLI) with a management PC using a terminal
emulation application connected either through the 

SERIAL 

DB9 port or though the 

MANAGEMENT

RJ45 port. Only one configuration session can be open at a time.

4.1

Command Line Interface (CLI)

The Command Line Interface (CLI ) is used to:

set IP address (default 192.168.1.1), Subnet Mask (default 255.255.255.0) and Gateway
(default 0.0.0.0)
set port speed and duplex
enables the user to select which ports or groups of ports receive the data stream copies
allows Any-to-Any ports to be configured as either inputs or outputs.

The VS-1200-S series factory default is off for all Any-to-Any ports.

4.1.1

Basic Functionality

Window Size Functionality:

 The CLI window is limited to 24 lines per screen and  80 characters

per line. If more data than can fit is presented, a “-more-” prompt is shown on the last line.

Character Handling:

 Printable character (ASCII code 32-126) and non-printable noted below:

Non-Printable Character

Description

<enter key>

Executes command; places command in history buffer

<backspace key>

Erases previous character entry; removes history buffer entry

Connectivity/Authentication Functionality:

 Connectivity to the configurable product is made

through the Management RJ45 or Serial DB9 port and authentication is required. This password
protection yields read-only access. To make configuration changes, Superuser (SU) mode must be
accessed with another password. See the '

Superuser Commands

' section for more information. 

Base Prompt:

 This is the text presented to the user logging in to use the CLI (default values

shown). All Usernames and passwords are case-sensitive.

Enter Username: Administrator
Enter Password: admin
>

Superuser log in:

Example: > SU

Enter Password: password
#

24

Summary of Contents for VS-1200-S Series



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands