manualshive.com logo in svg

Datacom Systems VS-1200-S Series, User Manual

The Datacom Systems VS-1200-S Series is a cutting-edge networking product designed to streamline your communication needs. Explore its features and functions with our comprehensive User Manual, available for free download at manualshive.com. Equip yourself with the knowledge to optimize your device's performance effortlessly.

Share
Download
background image

5

Contents

© 2011 Datacom Systems Inc

Table of Contents

Section 1 Terms of Use

9

................................................................................................................................... 9

1

Copyright

................................................................................................................................... 9

2

License Agreement

................................................................................................................................... 9

3

Trademark Attribution

................................................................................................................................... 9

4

Proprietary Notice

................................................................................................................................... 9

5

Certifications and Marks

................................................................................................................................... 10

6

Safety Notices and Warnings

Section 2 Overview

11

................................................................................................................................... 11

1

VS-1200-S Series Summary

................................................................................................................................... 12

2

What Shipped?

................................................................................................................................... 12

3

VS-1200-S Series Features and Benefits

................................................................................................................................... 13

4

VS-1200-S Series Common Specifications

................................................................................................................................... 13

5

VS-1200-S Series Model Specific Specifications

Section 3 Hardware

15

................................................................................................................................... 15

1

VS-1200-S Series Front Panels

................................................................................................................................... 16

2

Front Panel Description

.......................................................................................................................................................... 16

Pow er 

.......................................................................................................................................................... 16

Any-to-Any Ports 

.......................................................................................................................................................... 17

Managem ent Port 

................................................................................................................................... 17

3

Rear Panel Description

.......................................................................................................................................................... 17

Serial DB9 

.......................................................................................................................................................... 17

Pow er Sw itch (SFP series) 

.......................................................................................................................................................... 17

Rear Label (BT series) 

.......................................................................................................................................................... 18

Rear Labeling (SFP series) 

.......................................................................................................................................................... 18

Input Pow er 

Section 4 Initial Configuration

19

................................................................................................................................... 19

1

Command Line Interface (CLI)

.......................................................................................................................................................... 19

Basic Functionality 

.......................................................................................................................................................... 20

Passw ord Recovery 

.......................................................................................................................................................... 20

Basic Com m ands (Read Only Access) 

......................................................................................................................................................... 20

HELP (HE) or (?)

......................................................................................................................................................... 21

POWER STATUS (PO ST)

......................................................................................................................................................... 21

SHOW (SH)

......................................................................................................................................................... 22

SHOW GROUPS  (SH GR)

......................................................................................................................................................... 22

SHOW MANAGEMENT (SH MA)

......................................................................................................................................................... 23

SHOW PORT CONFIG  (SH PO CO)

......................................................................................................................................................... 23

SHOW PORT ROUTING (SH PO RO)

......................................................................................................................................................... 24

SHOW PRODUCT (SH PR)

......................................................................................................................................................... 24

SHOW TIME (SH TI)

......................................................................................................................................................... 24

SHOW USERS (SH US)

.......................................................................................................................................................... 24

Superuser Com m ands (Configuration Access) 

......................................................................................................................................................... 24

SU (SU)

Summary of Contents for VS-1200-S Series



























































































Reviews:

No comments

Related manuals for VS-1200-S Series

Eaton NR Installation And Operation Instructions Manual preview
NR
Brand: Eaton Pages: 12
Hama 78499 Operating Instructions Manual preview
78499
Brand: Hama Pages: 10
Hama 11467 Operating Instruction preview
11467
Brand: Hama Pages: 14
Comtrend Corporation ES-7211PoE User Manual preview
ES-7211PoE
Brand: Comtrend Corporation Pages: 2
Velux INTEGRA KLI 310 Quick Start Manual preview
INTEGRA KLI 310
Brand: Velux Pages: 9
Bluestream Custom Pro Matrix User Manual preview
Custom Pro Matrix
Brand: Bluestream Pages: 27
Omron B3SL Quick Start Manual preview
B3SL
Brand: Omron Pages: 4
F&F PF-421 TRMS Manual preview
PF-421 TRMS
Brand: F&F Pages: 10
WTI IPS-400 User Manual preview
IPS-400
Brand: WTI Pages: 56
IDT 89HPES12N3 User Manual preview
89HPES12N3
Brand: IDT Pages: 158
Broadcast Pix Flint LE 1000 Operator'S Manual preview
Flint LE 1000
Brand: Broadcast Pix Pages: 478
Dahua D-PFS4226-24ET-240 Quick Start Manual preview
D-PFS4226-24ET-240
Brand: Dahua Pages: 16
Exsys EX-1190HMVS-PD Manual preview
EX-1190HMVS-PD
Brand: Exsys Pages: 14
rackit MRS-815 Installer/User Manual preview
MRS-815
Brand: rackit Pages: 24
ADTRAN NetVanta 1560-48 Quick Start Manual preview
NetVanta 1560-48
Brand: ADTRAN Pages: 8
3Com SUPERSTACK 3 3870 Series Getting Started Manual preview
SUPERSTACK 3 3870 Series
Brand: 3Com Pages: 76
Secutron MRI-101P Installation Instructions preview
MRI-101P
Brand: Secutron Pages: 2
GE 97845 Instruction Manual preview
97845
Brand: GE Pages: 26

Brands by name

Popular brands

Load more brands