![background image](http://html1.mh-extra.com/html/dannmar/mb-240x/mb-240x_installation-and-operation-manual_3431293039.webp)
MB-240X Wheel Balancer
39
P/N 5900262 — Rev. A1 — Jan. 2021
ALU3
ALU3 Mode is used on Aluminum Alloy Wheels when
you want the weights applied to the Inner Plane and
the Outer Edge.
Select the ALU 3 Mode by pressing the
F
key until
the indicator next to the ALU 3 is lit.
Pull out the Inner Arm and place it on the Wheel
Inner Edge
and hold it there. Read the distance off
the arm and enter this data into the Balancer using the
Distance
+
/
—
key
. An
-A-
will appear in
the Inner Display Window and the distance value will appear in the Outer Display Window.
Return the
Inner Arm to its normal location.
Measure the width of the Wheel using the Wheel caliper. Enter this width into the Balancer using
the
Width
+
/
—
keys. An
-L-
will appear in the Inner Display Window and the value will appear in
the Outer Display Window.
Enter the Wheel diameter by reading the size off the Tire sidewall and enter this into the Balancer
using the
Diameter
+
/
—
keys. A
-D-
will appear in the Inner Display Window and the diameter
value will appear in the Outer Display Window.
While facing the Wheel, start spinning the Wheel in a clockwise
direction. Begin by pushing with
your hand against the Tire, then turn the Quick Nut black handles to increase the speed of rotation
until the Outer Display Window reads
run
.
Release the handles and wait. The display will go blank then the imbalance value will appear in the
Inner and Outer display windows.
Pull the brake to stop the Tire rotation.
⚠
WARNING
Do
not
attempt to stop a rotating Wheel with your hands. Always use the brake.
Even though there is no motor driving the Wheel it can severely injure you if it is in
motion.
When the Wheel stops, look at the values that appear in the Inner and Outer Windows on the
Display Panel; this is the unbalanced correction weight required for each plane measured in grams.
The value that appears in the Inner Window should be added to the
Inner Plane
of the Wheel.
The value that appears in the Outer Window should be added to the
Outer Edge
of the Wheel.
Turn the Wheel slowly to find the best location to put the weight on the Inner Plane. The Inner
Edge/Plane placement indicators located under the Inner Display Window light up or go out as you
move the Wheel to find the best location to place the weight. When all the indicators on the Inner
plane are lit engage the brake to hold the Wheel and apply the correct value weight to the
Inner
Plane
of the Wheel at the 12 o’clock position. (If the Inner Display Window shows
00
, do not add
any weight to the Inner Plane).
Turn the Wheel slowly again to find the best location for the weight on the Outer Plane. The Outer
Edge/Plane placement indicators located under the Outer Display Window light up or go out as
you move the Wheel to find the best location to put the weight.
Summary of Contents for MB-240X
