D2-10 Series Two-Post Lifts
27
P/N 5900249 — Rev. B — February 2021
8.
Tighten the Elbow Hydraulic Fitting appropriately; make sure to leave the unconnected end of the
fitting pointing towards the side of the Powerside Post that has the Clips for the Hydraulic Hose
(the same fitting on the Offside Post also needs to point towards the side with the Clips).
9.
Turn the Hydraulic Cylinder so that the Elbow Hydraulic Fitting is accessible from the bottom back
side of the Powerside Post.
Important
:
When routing Hydraulic Hoses, after they are positioned correctly, put them into the
nearby Clips and lightly crimp the Clips together. When all Hydraulic Hoses have been
installed, go back and fully crimp all of the Clips. You need to make sure the Clips are
tight enough to hold the Hydraulic Hoses in place but not so tight that the flow of
Hydraulic Fluid in the Hydraulic Hoses is affected.
There are Clips only along one side
of each Post
.
10.
Take the Medium Hydraulic Hose and connect the Straight End to the bottom of the Bulkhead Tee
Hydraulic Fitting and tighten securely.
11.
Push the Curved End of the Medium Hydraulic Hose down to the bottom of the Powerside Post
and connect it to the JIC connector on the Elbow Hydraulic Fitting on the Cylinder; tighten
securely.
12.
Switching to the Offside Post
, connect the other Elbow Hydraulic Fitting (NPT to JIC) to the
Hydraulic Hose Connector at the bottom of the Hydraulic Cylinder.
13.
Tighten the Elbow Hydraulic Fitting securely; make sure to leave the unconnected end of the fitting
pointing towards the side of the Lift Post with the Clips.
14.
Take the Long Hydraulic Hose, push the Curved End down through the Lift Post until it is at the
bottom of the Post, then connect the Curved End to the Elbow Hydraulic Fitting you just
connected and tighten securely.
Be sure to clip the Long Hydraulic Hose to the Clips in the Post.
15.
Carefully coil up and bind the rest of the Long Hydraulic Hose, then leave it resting on top of the
Offside Post until later in the installation. Cover the end of the Hydraulic Hose to prevent dirt or
debris from entering the Hydraulic System.
Important
: You should now have the Long Hydraulic Hose connected to the bottom of the
Hydraulic Cylinder in the Offside Post, with the rest of the Long Hydraulic Hose coiled
up at the top of the Offside Post. It will be connected to the rest of the Hydraulic
System later in the installation.
Summary of Contents for D2-10 Series
