Danfoss ECL Comfort 110 Operating Manual Download Page 2

Page: 2 / 52

VI.KT.G6.02

2 | © Danfoss | 2016.05

How to navigate?

Safety Note
To avoid injury of persons and damages to the device, it is absolutely necessary to read and
observe these instructions carefully. The warning sign is used to emphasize special conditions
that should be taken into consideration.

This symbol indicates that this particular piece of information should be read with
special attention.

Adjust temperatures and values.

Switch between menu lines.

Select / return.

2 sec.

Return to daily user menu.

What do the symbols mean?

Mode COMFORT<

Temp. 48@½

1000

The desired flow temperature is influenced by for example return temperature.

The actuator closes the control valve.

The actuator opens the control valve.
The actuator does not activate the valve.

The pump is ON.

The pump is OFF.

The controller is in setback mode.

The controller is in pre-setback mode (the symbol is blinking).

The controller is in comfort mode.

The controller is in pre-comfort mode (the symbol is blinking).

Summary of Contents for ECL Comfort 110





















































Search results

Summary of Contents for ECL Comfort 110

Reviews:

Related manuals for ECL Comfort 110

Brands by name

Popular brands

Danfoss ECL Comfort 110, Operating Manual

Search results

Summary of Contents for ECL Comfort 110

Reviews:

Related manuals for ECL Comfort 110

Brands by name

Popular brands