manualshive.com logo in svg

Daktronics ST-3170, Manual, Page: 6 / 50

Share
Download
Daktronics ST-3170 Manual Download Page 6

Introduction

2

Resources

Figure 2

 illustrates a Daktronics drawing label. 

This manual refers to drawings by listing the last 

set of digits. In the example, the drawing would 

be referred to as 

DWG-1007804

. All references to 

drawing numbers, appendices, figures, or other 

manuals are presented in bold typeface. 

Any drawings referenced in a particular section 

are listed at the beginning of it as shown below:

Reference Drawing:

System Riser Diagram .......................................................................................

DWG-1007804

Listed below are drawing types commonly used by Daktronics, along with the information 

each is likely to provide. All drawings referenced in this manual are found in 

Appendix A

.

• 

Schematic Drawings:

 describe internal power and signal wiring as well as 

interconnections between display sections; may also include driver addressing 

information

• 

Shop Drawings:

 describe mounting methods to structural elements, access method 

(front or rear), and power and signal entrance points

• 

System Riser Diagrams:

 describe power/signal connections between components 

and the control location; may also include control room layout and schematic

• 

Final Assembly Drawings: 

describe internal display component locations and 

detailed product appearance with part numbers and quantities

Daktronics identifies manuals by the DD or ED number located on the cover page. 

Ensure all applicable materials have been gathered before beginning the installation. 

Contact a Daktronics sales coordinator or project manager.

Daktronics Nomenclature

Part numbers will appear on certain drawings and illustrations. Most 

display components have a white label that lists the part number 

(

Figure 3

). Use this label to order a replacement. Refer to 

Section 

6: Daktronics Exchange and Repair & Return Programs (p�31)

 if 

replacing or repairing any display component.

Main Component Labels

Part Type

Part Number

Assembly; a collection of 

circuit boards

0A-XXXX-XXXX

Metal part

0M-XXXXXXX

Individual circuit board

0P-XXXX-XXXX

Fabricated metal assembly

0S-XXXXXX

Fuse

F-XXXX

Specially ordered part

PR-XXXXX-X

Transformer

T-XXXX

Wire or cable

W-XXXX

Drawing Number

Figure 2: 

Drawing Label

0P-1127-0024

SN:  

     2465

02/19/12 Rev. 1

Figure 3: 

Part Label

Accessory Labels

Component

Label

Grounding point

EXX

Power or signal jack

JXX

Power or signal plug for 

the opposite jack

PXX

Termination block for 

power or signal cable

TBXX

Summary of Contents for ST-3170



















































Reviews:

No comments