manualshive.com logo in svg

Daktronics ST-3170, Manual, Page: 32 / 50

Share
Download
Daktronics ST-3170 Manual Download Page 32

Maintenance & Troubleshooting

28

Replacing a Power Supply

Caution! Disconnect display power before servicing the power supplies to avoid 

electrical shock� Power supplies run on high voltage and may cause injury if touched� 
1� 

Access the table from the rear as described in 

Rear Access (p�27)

. 

2� 

Use a 5/16" nut driver to loosen the screws 

holding the power supply to the mounting 

bracket and the grounding ring for the power 

supply. Remove the power supply from the 

mounting bracket. 

3� 

Disconnect all the wires connected to the 

power supply and gently remove it from the 

display. 

4� 

Attach the new power supply to the mounting 

bracket inside the display and reconnect all 

wires. Refer to 

Figure 48

. 

5� 

Power up and test the display to verify the issue has been resolved. 

Light Strip Driver

Scorers tables with optional light strips will include an LED driver to control when the light 

strips turn on and off. Refer to 

Figure 49

 to view the location of light strip driver tray in the 

scorers table. 

Figure 49: 

Driver Tray Location

Figure 48: 

Power Supply

Summary of Contents for ST-3170



















































Reviews:

No comments