manualshive.com logo in svg

Daktronics ST-3170, Manual, Page: 33 / 50

Share
Download
Daktronics ST-3170 Manual Download Page 33

Maintenance & Troubleshooting

29

Refer to 

Figure 50

 for the components of an optional light strip driver tray. 

TENSION DANGEREUSE

À TERMINAUX EXPOSÉS.

DÉBRANCHEZ L'ÉLECTRICITÉ

AVANT L'ENTRETIEN.

ATTENTION

BEFORE SERVICING.

DISCONNECT POWER

AT EXPOSED TERMINALS.

HAZARDOUS VOLTAGE

CAUTION

TRANSFORMER

WHT

BLU

ORG

BRN

PNK

TAN

6

7

8

9

10

5

4

1

2

3

1

BLU ORG

2

PNK

3

TAN

4

POWER

TB-42 POWER

1

2

3

4

1

RED BLK

2

PNK

3

TAN

4

SIGNAL OUT

SIGNAL IN

CUR. LOOP

SIGNAL

TB-31

CR1

AC

AC

1

BLU PNK

2

GRY

3

VIO

4

SIGNAL

1

GAME

GAME

2

GAME

3

4

CLK

CLK

CLK

=STOP

= 0

SHOT

CLK

HORN HORN

Signal Terminal Block

4-Column 

LED Driver II

Address Jack

Power Terminal Block

Transformer

Light Strip Output 

Terminal Block

Driver Status 

Indicators 

Figure 50: 

Light Strip Driver Tray Components

The light strip output terminal block determines when the light strips will illuminate. By 

default, end-of-period light strips are triggered when the game clock equals 0, and clock 

stopped light strips are triggered when the clock equals stopped. Either type of light 

strip may instead be set to illuminate when the shot clock horn or the game clock horn 

sounds. Move the gray wire to the appropriate terminal for the desired function. 
When troubleshooting 4-column driver problems, two diagnostic LED indicators labeled 

DS1

 and 

DS2

 provide the following driver status information: 

LED

Color

Function Operation

Summary

DS1

Red

Signal RX

Steady on or 

blinking

On or blinking when driver is receiving signal

Off when there is no signal

DS2

Green

Power

Steady on

On and steady when driver is receiving power

Note: 

While it is necessary to have the display powered on to check the LED status 

indicators, always disconnect power before servicing. 

Replacing a Driver

If the driver status indicators do not appear to be working correctly, it may be necessary 

to replace the driver.

1� 

Open the table from the rear as described in 

Rear Access (p�27)

.

2� 

Disconnect all plugs from the driver by squeezing together the locking tabs and 

pulling the connectors free. It may be helpful to label the cables or take a picture to 

know which cable goes to which connector when attaching the new driver.

3� 

Remove the wing nuts securing the driver to the driver tray.

4� 

Carefully lift the driver from the display and place it on a clean, flat surface.

5� 

Position a new driver over the screws and tighten the nuts.

Summary of Contents for ST-3170



















































Reviews:

No comments