manualshive.com logo in svg

Daktronics ST-3170, Manual, Page: 30 / 50

Share
Download
Daktronics ST-3170 Manual Download Page 30

Maintenance & Troubleshooting

26

Recommended Tools

When performing maintenance work on the display, Daktronics recommends using the 

following tools and placing them in a convenient, easy-to-use location. 

Tool

Part Number Use

T25 Torx Bit

T-1118

Opens rear access panels and removes front face

5/16" T-handle Wrench TH-1200

Engages table interconnect latches

5/16" Nut Driver

TH-1156

Removes power supplies

3/8" Nut Driver

TH-1068

Removes LED edge light strips

The only tool provided with the table is the T-handle wrench. Additional replacement 

tools may be ordered directly from Daktronics. Refer to 

Daktronics Exchange and Repair 

& Return Programs (p�31)

. 

Component Location & Access

Scorers tables are designed for either front or rear access, depending on site 

requirements and customer preference. 
While components in front-access displays are simply removed from the front, access 

doors in rear-access displays must be removed to reach the internal display components.

Front Access

1� 

Disconnect the power to the display. 

2� 

To access the face panel screws, lift up one top pad and use a small pick or 

screwdriver to depress both spring pins on each hinge connecting the pad to the 

table. Pull the spring pins inward and down. Refer to 

Figure 45

. 

3� 

Remove the pad and set it aside; repeat for all top pads. 

4� 

Remove all T25 Torx screws along the top plex retainer as shown in 

Figure 46

. Set the 

top plex retainer aside.

Figure 45: 

Remove Top Pad Hinges

     

Figure 46: 

Remove Torx Screws

Face Panel

Top Plex Retainer

Top Retainer

5� 

Tilt the face panel forward and lift up to remove. 

Summary of Contents for ST-3170



















































Reviews:

No comments