manualshive.com logo in svg

Daktronics ST-3170, Manual, Page: 5 / 50

Share
Download
Daktronics ST-3170 Manual Download Page 5

Introduction

1

1  Introduction

This manual explains the installation, maintenance, and troubleshooting of Daktronics 

backlit scorers tables. For additional information regarding safety, installation, operation, 

or service, refer to the telephone numbers listed in 

Section 6: Daktronics Exchange and 

Repair & Return Programs (p�31)

. This manual is not specific to a particular installation. 

Contract-specific information takes precedence over any other general information 

found in this manual. 

Important Safeguards

•  Read and understand all instructions before beginning the installation process.
•  Disconnect power to the display when not in use or when servicing.
•  Disconnect power to the display before servicing power supplies to avoid electrical 

shock. Power supplies run on high voltage and may cause physical injury if touched 

while powered.

•  Do not disassemble control equipment or electronic controls of the display; failure to 

follow this safeguard will make the warranty null and void. 

•  Do not modify the structure or attach any panels or coverings to the display without 

the express written consent of Daktronics.

•  Do not drop the control equipment or allow it to get wet.

Specifications

Power specifications as well as serial 

and model number information 

can be found on an ID label similar 

to 

Figure 1

, located inside the right 

rear access door. Refer to the table 

below for brief descriptions of the 

models in this manual: 

Model #

Description

Dimensions

Weight

Power (120 VAC)

ST-3170-5

Backlit Ad Panel, 

seats 2 scorers

3.00' H x 5.33' W x 2.70' D

(914 mm, 1.63 m, 823 mm)

160 lb  

(73 kg)

1260 Watts, 10.5 Amps

ST-3170-10 Backlit Ad Panel, 

seats 4 scorers

3.00' H x 10.26' W x 2.70' D

(914 mm, 3.13 m, 823 mm)

260 lb  

(118 kg)

1308 Watts, 10.9 Amps

Notes: 

•  Widths shown include side padding. Subtract 5" (127 mm) for width without the padding.
•  Height and depth shown is for table in stationary mode. Tables are 3.45' (1.05 m) tall and 2.40' 

(732 mm) deep in transport mode.

•  Power shown includes max load placed on table including convenience outlets.

Please have the assembly number, model number, and the date manufactured on hand 

when calling Daktronics customer service to ensure the request is serviced as quickly as 

possible. Also provide the facility name and/or job number if known.

DAKTRONICS 201 DAKTRONICS DR. BROOKINGS, SD PHONE 800-325-8766

SUITABLE FOR SERVICING ONLY WHEN DE-ENERGIZED

PUET FAIRE L'OBJET D'UN ENTRETIEN UNIQUEMENT S'IL EST HORS TENSION

LL-3858356 R01

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION

Figure 1: 

Specifications Label

Summary of Contents for ST-3170



















































Reviews:

No comments