background image

ESIE16-03B

 

 

 

22/08/16 

Version 1.1

Page 3

SA R32 Sky-Air RZAG-L

Part 1. Introduction  ....................................................................................................................7

1.1. Version log  .................................................................................................................................................7

1.2. Safety precautions  .....................................................................................................................................8

1.2.1. Meaning of symbols  ....................................................................................................................................... 8
1.2.2. Warnings  ........................................................................................................................................................ 8
1.2.3. Cautions  ....................................................................................................................................................... 10
1.2.4. Information  ................................................................................................................................................... 10

1.3. General operation  ....................................................................................................................................11

1.4. How to use  ...............................................................................................................................................12

1.4.1. Interactive information flow ........................................................................................................................... 12
1.4.2. Parts of the book  .......................................................................................................................................... 13

1.4.2.1. The introduction chapter  .......................................................................................................................... 13
1.4.2.2. The troubleshooting chapter  .................................................................................................................... 13
1.4.2.3. The repair chapter .................................................................................................................................... 13
1.4.2.4. The maintenance chapter  ........................................................................................................................ 13
1.4.2.5. Appendices  .............................................................................................................................................. 13

1.4.3. Contact information  ...................................................................................................................................... 13

Part 2. Troubleshooting ...........................................................................................................15

2.1. Error codes check  ....................................................................................................................................15

2.1.1. Error codes via remote controller  ................................................................................................................. 15

2.1.1.1. Error codes via wired remote controller BRC1E  ...................................................................................... 15
2.1.1.2. Error codes via wireless remote controller BRC7  .................................................................................... 17

2.1.2. Error codes via outdoor unit PCB ................................................................................................................. 19

2.1.2.1. How to retrieve error codes ...................................................................................................................... 19
2.1.2.2. How to reset error codes .......................................................................................................................... 21
2.1.2.3. History of error codes and warnings  ........................................................................................................ 22
2.1.2.4. Content of retry  ........................................................................................................................................ 22

2.2. Error based troubleshooting .....................................................................................................................23

2.2.1. Indoor unit  .................................................................................................................................................... 24

2.2.1.1. “A1-01” – Indoor unit PCB abnormality  .................................................................................................... 24
2.2.1.2. “A3-00” – Drain water level system abnormality  ...................................................................................... 24
2.2.1.3. “A6-00” – Indoor unit fan motor abnormality  ............................................................................................ 24
2.2.1.4. “AJ-00” – Capacity setting abnormality  .................................................................................................... 25
2.2.1.5. “C1-00” – Transmission error (indoor & adapter PCB)  ............................................................................ 25
2.2.1.6. “C4-00” – Heat exchanger thermistor abnormality ................................................................................... 26
2.2.1.7. “C5-00” – Intermediate heat exchanger thermistor abnormality  .............................................................. 26
2.2.1.8. “C9-00” – Suction air thermistor abnormality  ........................................................................................... 27
2.2.1.9. “CC-00” – Humidity sensor system abnormality  ...................................................................................... 27
2.2.1.10. “CJ-00” – Remote controller thermistor abnormality  .............................................................................. 27

2.2.2. Outdoor unit .................................................................................................................................................. 28

2.2.2.1. “E1-00” – Outdoor unit PCB abnormality  ................................................................................................. 28
2.2.2.2. “E3-00” – Discharge pressure abnormality .............................................................................................. 28
2.2.2.3. “E4-00” – Suction pressure abnormality  .................................................................................................. 29
2.2.2.4. “E5-00” – Compressor motor lock or overheated ..................................................................................... 29
2.2.2.5. “E7-00” – Fan motor abnormality  ............................................................................................................. 30
2.2.2.6. “E9-00” – Electronic expansion valve abnormality ................................................................................... 31
2.2.2.7. “F3-00” – Discharge pipe temperature abnormality  ................................................................................. 31
2.2.2.8. “H3-00” – High pressure switch abnormality ............................................................................................ 32
2.2.2.9. “H4-00” – Low pressure switch abnormality ............................................................................................. 33
2.2.2.10. “H9-00” – Outdoor air temperature thermistor abnormality .................................................................... 33
2.2.2.11. “J3-00” – Discharge pipe thermistor abnormality  ................................................................................... 33
2.2.2.12. “J5-00” – Suction pipe thermistor abnormality  ....................................................................................... 34
2.2.2.13. “J6-00” – Outdoor heat exchanger thermistor abnormality  .................................................................... 34
2.2.2.14. “J7-00” – Intermediate heat exchanger thermistor abnormality  ............................................................. 34
2.2.2.15. “J8-00” – Liquid pipe thermistor abnormality .......................................................................................... 35
2.2.2.16. “L1-00” – Outdoor main PCB abnormality .............................................................................................. 35
2.2.2.17. “L5-00” – Output overcurrent detection .................................................................................................. 36

Summary of Contents for RZAG100L7V1B





























































































































Reviews: