background image

6

English

Control box

13/16 (20)  or more

Ceiling

Inspection hatch

A

Inspection 

hatch 1

17-3/4×17-3/4 

(450×450)

Inspection 

hatch 3

Control box

Control box

unit: in. (mm)

31-1/2

(800)

31-1/2

(800)

Arrow A-1

Arrow A-2

Inspection hatch 2

(Indoor unit size 

+11-13/16 (300) 

or more)

(Indoor unit 

size or more)

7-7/8 (200) or less

D=B+11-13/16  (300) or more

B

< In the case of (1)-2, 3 >

Fig. 4

Table 1 

(unit [in. (mm)])

Model

B

C

D

15·18·24 type

39-3/8 

(1000)

40-7/8 
(1038)

51-3/16 

(1300)

30·36·48 type

55-1/8 
(1400)

56-5/8 

(1438)

66-15/16 

(1700)

54 type

61 

(1550)

62-1/2 
(1588)

72-13/16 

(1850)

(2)  Mount canvas ducts to the discharge and suction so 

that the vibration of the indoor unit will not be trans-

mitted to the ducts or ceiling. Furthermore, attach 

sound absorbing material (thermal insulation mate-

rial) to the duct inner walls and anti-vibration rubber 

to the suspension bolts (refer to 8. DUCT WORK).

(3)  The indoor unit is set to standard external static 

pressure.

• 

If external static pressure is higher or lower than the 

standard set value, the remote controller may be used 

to make field setting change in the external static pres

-

sure.  
Refer to 

10. FIELD SETTING

.

(4)  Open installation holes  

(in the case of installation onto the existing ceiling).

• 

Open the installation holes on the ceiling of the instal-
lation location, and work on the refrigerant piping, drain 
piping, remote controller wiring (unless a wireless re-
mote controller is used), and wiring between the indoor 
and outdoor units to the piping connection port and 
wiring connection port of the indoor unit (refer to each 
piping and wiring procedure items).

• 

Ceiling framework reinforcement may be required in 
order to keep the ceiling horizontal and prevent ceiling 
vibration after opening the ceiling holes. For details, 
consult your building and interior work contractors.

(5)  Install the suspension bolts.

• 

Use either a M8-M10 size bolt or equivalent. 

Use hole-in-anchors for the existing bolts and embed

-

ded inserts or foundation bolts for new bolts, and fix the 
indoor unit firmly to the building so that it may withstand 

the weight of the unit. 
In addition, adjust clearance (2-4 in. (50-100 mm)) from 
the ceiling in advance.

<Installation examples>

Foundation bolt

Suspension bolt

Indoor

unit

Ceiling slab

Long nut or 
turnbuckle

Note) Components shown in the figure above are 

all local procurement.

(6)  In the case of changing the preset suction to bottom 

side suction, replace the chamber cover and the suc-

tion flange. (Refer to Fig. 5)

1.  Remove the suction flange and chamber cover.
2.  Replace the suction flange and the chamber cover.

 CAUTION

• 

Secure a sufficient service space for the drain pan and 

electrical components before installing the indoor unit.

• 

Secure a sufficient service space for the filter chamber, 

and peripheral components before installing the indoor 
unit.

01_EN_3P493125-6E.indd   6

2022/08/03   10:36:08

Summary of Contents for FXMQ15TBVJU






















Reviews: