3
English
2. BEFORE INSTALLATION
When unpacking the indoor unit or moving the unit after
unpacked, hold the hanger brackets (4 locations) and do
not apply force to other parts (particularly refrigerant pip-
ing, drain piping).
•
Make sure to check in advance that the refrigerant to be
used for installation work is R410A.
(The air conditioner will not properly operate if a wrong
refrigerant is used.)
•
For installation of the outdoor unit and additional refriger-
ant charge, refer to the installation manual attached to the
outdoor unit.
•
Do not throw away the accessories until the installation
work is completed.
•
Do not damage the equipment or property when carrying
the indoor unit into the room.
(1) Measure the unit with packaging to ensure the unit
can be carried safely while still packaged.
(2) Determine the route to carry the unit into the room.
(3) Do not unpack the unit until it is carried to the installa-
tion location.
Where unpacking is unavoidable, use a sling of soft
material or protective plates together with a rope when
lifting, to avoid damage or scratches to the indoor unit.
•
After the indoor unit is carried into the room, to avoid the
indoor unit from getting damaged, take measures to protect
the indoor unit with packing materials.
•
Have the customer actually operate the air conditioner
while looking at the operation manual.
Instruct the customer how to operate the air conditioner
(particularly cleaning of the air filters, operation pro cedures,
and temperature adjustment).
•
Do not use the air conditioner in a salty atmosphere such
as coastal areas, vehicles, vessels or where voltage fluc
-
tuation is frequent such as factories.
•
Take off static electricity from the body when carrying out
wiring and the control box cover is removed.
The electric parts may be damaged.
2-1 ACCESSORIES
Check if the following accessories are attached to the
indoor unit.
Name
(1) Metal
clamp
(2) Drain
hose
(3) Duct flange connection
screw
Quantity
1 pc.
1 pc.
See below
Shape
15·18·24
type
18 pcs.
30·36·48
type
30 pcs.
54
type
34 pcs.
Name
Joint insulating
material
(6) Sealing
material
(7) Sealing
material
(8) Clamp
Quantity
1 each
1 sheet
2 sheets
8 pcs.
Shape
Thin
(4) For liquid
piping
Thick
(5) For gas
piping
Large
(Dark gray)
Medium
(Dark gray)
Name
(9) Washer clamp
(10) Wire sealing
material
(11) Washer for
hanger bracket
Quantity
4 pcs.
2 sheets
8 pcs.
Shape
Small
(Gray)
Name
(12) Conduit
mounting plate
Others
Quantity
1 pc.
• Operation
manual
• Installation
manual
Shape
2-2 OPTIONAL ACCESSORIES
• A remote controller is required for the indoor unit.
•
There are 2 kinds of remote controllers; wired type and
wireless type.
Install the remote controller to the place where the cus-
tomer has given consent.
Refer to the catalog for the applicable model.
(Refer to the installation manual attached to the remote
controller for how to install.)
• The indoor unit can be switched to lower suction.
(Refer to 4. PREPARATION BEFORE INSTALLATION.)
The side cover plate (KDBD63A160) is required in the case
of wiring from the bottom surface at bottom suction.
For installation work, refer to the installation manual provid-
ed with the side cover plate. <Except for 30·36·48·54 type>
CARRY OUT THE WORK GIVING CAUTION
TO THE FOLLOWING ITEMS AND AFTER
THE WORK IS COMPLETED CHECK THESE
AGAIN.
(1) Items to be checked after the installation work is
completed
Items to be checked
In case of defective
Check
column
Are the indoor and outdoor
units rigidly fixed?
Drop · vibration ·
noise
Are the installation works of
the outdoor and indoor units
completed?
Does not operate ·
burnout
Have you carried out air tight
test with the test pressure
specified in the outdoor unit
installation manual?
Does not cool/
Does not heat
01_EN_3P493125-6E.indd 3
2022/08/03 10:36:07
