DAF 95XF Maintenance Manual Download

Page: 90 / 188

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

Inspection and adjustment

series

3-30

3.22 CHECKING THE BRAKE LINING THICKNESS

Checking the brake lining thickness (FTP
axle excepted)

Pressurise the air brake system (pressure
switch should cut out) and make sure that
the vehicle’s parking brake is not activated.

Check the brake lining thickness through
the openings in the dust cover.

Replace the brake lining if it is worn down to
the wear indicator mark on the brake lining.

Note:

If in doubt about the amount of brake lining
wear, release the brakes and remove the
dust cover.

M6012

M6002

Checking the brake lining thickness (FTP
axle)

Pressurise the air brake system (pressure
switch should cut out) and make sure that
the vehicle’s parking brake is not activated.

Check the brake lining thickness through
the openings in the dust cover.

Replace the brake lining if it is worn down to
the wear indicator mark on the brake lining.

Note:

If in doubt about the amount of brake lining
wear, release the brakes and remove the
dust cover.

R6 00 677



200424

Summary of Contents for 95XF





























































































































































































Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands

DAF 95XF, Maintenance Manual

Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands