DAF 95XF Maintenance Manual Download

Page: 169 / 188

series

Draining and filling

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

5-11

1354 and 1355 (T) axle

Draining the wheel hub

Position the vehicle on a level surface.

Position the wheels in such a way that the
drain/filler plug (A) is on the underside.

Remove the drain/filler plug (A) and level
check plug (B) and drain the oil.

A8 00 363

Filling the wheel hub

Position the vehicle on a level surface.

Position the wheels in such a way that the
drain/filler plug (A) is on the top side.

Fill the hub with the specified quantity of oil.
See ”Technical data”.

Check the oil level after approximately 5
minutes. See ”Inspection and adjustment”.

Fit the level check plug (B) and the
drain/filler plug (A) using the special torx
wrench (DAF no. 1329422) and tighten the
plug to the specified tightening torque. See
”Technical data”.

A8 00 364



200424

Summary of Contents for 95XF





























































































































































































Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands

DAF 95XF, Maintenance Manual

Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands