DAF 95XF Maintenance Manual Download Page 138

Page: 138 / 188

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

Removal and installation

series

4-18

VF engine

Removing the valve cover

Clean the area around the valve cover.

Remove the attachment bolts from the valve
cover.

Remove the valve cover and the gasket.

Installing the valve cover

Clean the sealing face of the valve cover.

Fit the valve cover using the valve cover
gasket.
The valve cover gasket, if not damaged,
may be reused (do not use solvents for
cleaning the gasket).
The marking “TOP” on the gasket should
point in the direction of the valve cover.

Fit the attachment bolts of the valve cover
and tighten them to the specified torque.
See “Technical data”.



200424

Summary of Contents for 95XF





























































































































































































Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands

DAF 95XF, Maintenance Manual

Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands