DAF 95XF Maintenance Manual Download Page 80

Page: 80 / 188

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

Inspection and adjustment

series

3-20

Adjusting the V-belt tension of the air
conditioning compressor drive

Slacken the attachment bolt (1) in the
clamping block (2) and slacken the
attachment bolt of the threaded spindle on
the cylinder block.

Slacken the attachment bolts on the
compressor.

Reposition the compressor using the lock
nuts (3) until the correct V-belt tension is
achieved. See “Technical data”.

M2127

Adjusting the belt (10-rib) tension of fan and
alternator drive

Slacken the attachment bolt (1) in the
clamping block (2) and slacken the
attachment bolt of the threaded spindle on
the cylinder block.

Slacken the attachment bolt (3) in the
alternator support.

Shift the alternator using the lock nuts (4)
until the correct belt tension is achieved,
see “Technical data”.

M2128

Adjusting the belt (6-rib) tension of water
pump drive

Slacken the central nut (1) of the tensioner.

Shift the tensioner using the bolt (2) until the
correct belt tension is achieved, see
“Technical data”.

M2129



200424

Summary of Contents for 95XF





























































































































































































Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands

DAF 95XF, Maintenance Manual

Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands