DAF 95XF Maintenance Manual Download Page 144

Page: 144 / 188

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

Removal and installation

series

4-24

4.16 REMOVAL AND INSTALLATION, WHEEL HUB

FRONT AXLE/LEADING REAR AXLE/TRAILING AXLE 09N075

3 4

5 6

11 12

S7 00 401

Removing the wheel hub

Jack up the axle until the wheels are clear
from the floor and position suitable stands
under the axle.

Release the brake shoes.

Remove the hub cap (2).

Tap back the locking washer (4) and
remove the lock nut (3) from the axle journal
using the socket spanner (A), special tool
(DAF no. 0535832).

Remove the locking washer (4) and the
circlip (5) from the axle journal.

Position a tyre lift under the wheel.

S7 00 084



200424

Summary of Contents for 95XF





























































































































































































Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands

DAF 95XF, Maintenance Manual

Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands