DAF 95XF Maintenance Manual Download Page 148

Page: 148 / 188

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

Removal and installation

series

4-28

LEADING REAR AXLE 09N044 (FTP-TYPE VEHICLES)

S7 00 640

Removing the wheel hub

Remove the hub cap (1) using special tool
(DAF no. 1329498).

Lift the leading rear axle and support it
properly.

Remove the split pin (2) and the hub nut (3).

Remove the outer wheel bearing (4).

Remove the hub (6) with the wheel.

Installing the wheel hub

Apply new grease to the hub (6).

Install the hub with the wheel.

Install the outer wheel bearing (4).

Fit the hub nut (3).

Adjust the wheel bearing play, see chapter
“Inspection and adjustment”.

Fit the split pin (2).

Lower the leading rear axle.

Fit the hub cap using special tool (DAF no.
1329894). Tighten the hub cap to the
specified torque, see “Technical data”.

Adjust the brakes.



200424

Summary of Contents for 95XF





























































































































































































Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands

DAF 95XF, Maintenance Manual

Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands