DAF 95XF Maintenance Manual Download Page 84

Page: 84 / 188

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

Inspection and adjustment

series

3-24

Bleeding the XF engine fuel system

While bleeding the fuel system, fuel
will escape. Collect this fuel,
bearing in mind the risk of fire.

Open the bleed screw (1) on the filter
housing.

Using the hand pump (2), pump fuel
through the system until fuel without air
bubbles flows through the bleed screw.

Close the bleed screw (1).

i 400172

Bleeding the XE engine fuel system

While bleeding the fuel system, fuel
will escape. Collect this fuel,
bearing in mind the risk of fire.

Dirt in the fuel system can lead to
significant damage to pump units
and housing.

Open the bleed screw (1) on the filter
housing.

Using the hand pump (2), pump fuel
through the system until fuel without air
bubbles flows through the bleed screw.

Close the bleed screw (1).

i 400252



200424

Summary of Contents for 95XF





























































































































































































Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands

DAF 95XF, Maintenance Manual

Search results

Summary of Contents for 95XF

Reviews:

Related manuals for 95XF

Brands by name

Popular brands