D-Link ENW-3503 User Manual Download Page 9

Page: 9 / 64

1 INTRODUCTION

PLANET ENW-3503 User's Manual

1-3

1.2.2.

Features

Compatible with most notebook computers and

PCMCIA Card and Socket Service drivers.
2.

High degree of reliability letting you out of

trouble.
3.

Easy to install and play.

Support most of the popular Network Operating

Systems.
5.

Include popular Fax/Modem communication

programs.
6.

Hot swappable.

Feature concurrent use of Ethernet LAN and

Fax/Modem.
8.

NE2000 compatible.

1.3. SYSTEM REQUIREMENTS

•

An IBM compatible PC or notebook computer with

386SX or faster processor

•

At least one type II PCMCIA socket

•

PCMCIA release 2.1 compliant Card Services and

Socket Services

•

Drivers and utilities provided with this product

•

RJ11 jack for connecting to a phone receptacle

•

RJ45 jack for 10Base-T connectivity to your

network resources

•

Driver software loaded on your PC

•

Data and/or fax communications software.

1.4. PACKAGE CONTENTS

•

Multifunction ENW-3503 PC Card

•

PCMCIA cable with RJ-11 and RJ-45 plugs

Summary of Contents for ENW-3503

































































Search results

Summary of Contents for ENW-3503

Reviews:

Related manuals for ENW-3503

Brands by name

Popular brands

D-Link ENW-3503, User Manual

Search results

Summary of Contents for ENW-3503

Reviews:

Related manuals for ENW-3503

Brands by name

Popular brands