D-Link ENW-3503 User Manual Download Page 15

Page: 15 / 64

INSTALLATION

PLANET ENW-3503 User's Manual

2-5

4.Check the card settings. If current settings are correct, select

Start Installation

and go to step 5. Otherwise, select

Modify Parameters

to change settings.

5.Select the appropriate values then press

Enter

. When you

are finished, press

to exit.

6.Installation program starts installing drivers and
modifying

CONFIG.SYS

and

PROTOCOL.INI

Select

Yes

then press

Enter

to modify the files.

7.Now, the installation is completed.
8.Reboot the computer to load driver and start LAN Manager.

Example of PROTOCOL.INI:

[PROTMAN]

DRIVERNAME = PROTMAN$
DYNAMIC = YES
PRIORITY = NETBEUI

[NETBEUI_XIF]

Drivername = netbeui$
SESSIONS = 6
NCBS = 12
BINDINGS = "LMNDIS_NIF"
LANABASE = 0

[LMNDIS_NIF]
; protocol.ini session for multifunction
LAN/MODEM driver.

IOADDRESS = 0x320
INTERRUPT = 11
DRIVERNAME = LMNDIS$

2.2.3.

Packet Driver Installation

1.Run

INSTALL.EXE

file in the driver diskette

(A:\INSTALL).

Summary of Contents for ENW-3503

































































Search results

Summary of Contents for ENW-3503

Reviews:

Related manuals for ENW-3503

Brands by name

Popular brands

D-Link ENW-3503, User Manual

Search results

Summary of Contents for ENW-3503

Reviews:

Related manuals for ENW-3503

Brands by name

Popular brands