D-Link DSL-2540T User Manual Download Page 73

Page: 73 / 112

DSL-2540T ADSL Router User Guide

RIP

The Router supports RIP v1 and RIP v2 used to share routing tables with other Layer 3 routing devices on your local
network or remote LAN.

RIP System Wide Configuration window

To enable RIP, select

Enabled

from the

RIP

pull-down menu, select the

Protocol

(

RIPv1

and

RIPv1 Compatible

) and

Direction

(

Out

, or

Both

), and click

Apply

The RIPv1 Compatible option will transmit RIPv2 broadcast packets and receive both RIP v1 and RIP v2 packets.

The direction configuration refers to the RIP request. Select In to allow RIP requests from other devices. Select Out to
instruct the Router to make RIP requests for routing tables from other devices. Select

Both

to share routing tables in

both directions.

Summary of Contents for DSL-2540T

















































































































Search results

Summary of Contents for DSL-2540T

Reviews:

Related manuals for DSL-2540T

Brands by name

Popular brands

D-Link DSL-2540T, User Manual

Search results

Summary of Contents for DSL-2540T

Reviews:

Related manuals for DSL-2540T

Brands by name

Popular brands