D-Link DSL-2540T User Manual Download Page 17

Page: 17 / 112

DSL-2540T ADSL Router User Guide

Wizard

To use the Setup Wizard, click the

Run Wizard

button in the first browser window and follow the instructions in the

pop-up window that appears.

The initial window summarizes the setup process. Click the

Next

button to proceed. You may stop using the Setup

Wizard at any time by clicking the

Exit

button. If you exit the wizard you will return to the

Setup Wizard

window

without saving any of the settings changed during the process.

The first pop-up window of the Setup Wizard lists the basic steps in the process. These steps are as follows:

Set the system time.

Configure the connection to the Internet.

Save the new configuration settings and reboot the system.

Summary of Contents for DSL-2540T

















































































































Search results

Summary of Contents for DSL-2540T

Reviews:

Related manuals for DSL-2540T

Brands by name

Popular brands

D-Link DSL-2540T, User Manual

Search results

Summary of Contents for DSL-2540T

Reviews:

Related manuals for DSL-2540T

Brands by name

Popular brands