DES-3028 DES-3028P DES-3028G DES-3052 DES-3052P Layer 2 Fast Ethernet Switch CLI Reference Manual
172
config access_profile
Purpose
Used to configure an access profile on the Switch and to define specific values that will be
used to by the Switch to determine if a given packet should be forwarded or filtered. Masks
entered using the
create access_profile
command will be combined, using a logical AND
operational method, with the values the Switch finds in the specified frame header fields.
Specific values for the rules are entered using the
config access_profile
command, below.
Syntax
config access_profile profile_id <value 1-256> [add access_id [auto_assign | <value 1-
65535>] [ethernet {vlan <vlan_name 32> | source_mac <macaddr> | destination_mac
<macaddr> | 802.1p <value 0-7> | ethernet_type <hex 0x0-0xffff> } | ip {vlan <vlan_name
32> | source_ip <ipaddr> | destination_ip <ipaddr> | dscp <value 0-63> | [icmp | igmp |
tcp {src_port <value 0-65535> | dst_port <value 0-65535> | urg | ack | psh | rst | syn | fin }
| udp {src_port <value 0-65535> | dst_port <value 0-65535>} | protocol_id <value 0-255>]}
| packet_content offset <value 0-76> <hex0x0-0xffffffff> {offset <value 0-76> <hex 0x0-
0xffffffff> {offset <value 0-76> <hex 0x0-0xffffffff> {offset <value 0-76> <hex 0x0-0xffffffff>
{offset <value 0-76> <hex 0x0-0xffffffff>}}}}] port [<portlist> | all ] [permit{ priority <value
0-7> replace_priority_with <value 0-7} | rx_rate [no_limit |<value 64-1024000>]} | deny]
{time_range <range_name 32>} | delete access_id <value 1-65535>]
Description
The
config access_profile
command is used to configure an access profile on the Switch and
to enter specific values that will be combined, using a logical AND operational method, with
masks entered with the
create access_profile
command, above.
Parameters
profile_id <value 1-256>
Enter an integer used to identify the access profile that will be
configured with this command. This value is assigned to the access profile when it is created
with the
create access_profile
command. The profile ID sets the relative priority for the profile
and specifies an index number that will identify the access profile being created with this
command. Priority is set relative to other profiles where the lowest profile ID has the highest
priority. The user may enter a profile ID number between
1
and
256
.
add access_id <value 1-65535>
Adds an additional rule to the above specified access profile.
The value is used to index the rule created. For information on number of rules that can be
created for a given port, please see the introduction to this chapter.
auto_assign –
Choose this parameter to configure the Switch to automatically assign a
numerical value (between
1
and
65535
) for the rule being configured.
ethernet
Specifies that the Switch will look only into the layer 2 part of each packet.
vlan <vlan_name 32>
Specifies that the access profile will apply to only to this VLAN.
source_mac <macaddr>
Specifies that the access profile will apply to only packets with
this source MAC address.
destination_mac <macaddr>
Specifies that the access profile will apply to only packets
with this destination MAC address.
802.1p <value 0-7>
Specifies that the access profile will apply only to packets with this
802.1p priority value.
ethernet_type <hex 0x0-0xffff>
Specifies that the access profile will apply only to packets
with this hexadecimal 802.1Q Ethernet type value in the packet header.
