D-Link DAP-1360 User Manual Download Page 14

Page: 14 / 270

DAP-1360

Wireless N300 Access Point & Router

User Manual

Installation and Connection

Connecting to PC

PC with Ethernet Adapter

1. Make sure that your PC is powered off.

2. Connect an Ethernet cable between the LAN port located on the back panel of the access

point and the Ethernet port of your PC.

3. Connect the power cord to the power connector port on the back panel of the access point,

then plug the power adapter into an electrical outlet or power strip.

4. Turn on the access point by pressing the

ON/OFF

button on its back panel.

5. Turn on your PC and wait until your operating system is completely loaded.

Now you need to configure an IP address for the Ethernet adapter of your PC.

Configuring IP Address in OS Windows XP

1. Click the

Start

button and proceed to the

Control Panel > Network and Internet

Connections > Network Connections

window.

2. In the

Network Connections

window, right-click the relevant

Local Area Connection

icon and select the

Properties

line in the menu displayed.

Figure 3. The

Network Connections

window.

Page

of 270

Summary of Contents for DAP-1360















































































































































































































































































Search results

Summary of Contents for DAP-1360

Reviews:

Related manuals for DAP-1360

Brands by name

Popular brands

D-Link DAP-1360, User Manual

Search results

Summary of Contents for DAP-1360

Reviews:

Related manuals for DAP-1360

Brands by name

Popular brands