D-Link DAP-1360 User Manual Download Page 10

Page: 10 / 270

DAP-1360

Wireless N300 Access Point & Router

User Manual

Overview

Product Appearance

Front Panel

Figure 1. Front panel view.

LED

Mode

Description

Power

Solid green

The device is powered on.

No light

The device is powered off.

WLAN

Solid green

The device's WLAN is on.

Blinking green

The WLAN interface is active (upstream or
downstream traffic).

No light

The access point's WLAN is off.

WPS

Blinking green

Attempting to add a wireless device via the WPS
function.

No light

The WPS function is not in use.

LAN

Solid green

A device (computer) is connected to the port, the
connection is on.

Blinking green

The port is active (upstream or downstream traffic).

No light

The cable is not connected to the port.

Internet

Solid green

The Internet connection is on.

Blinking green

The WAN interface is active (upstream or downstream
traffic).

No light

The cable is not connected.

Page

of 270

Summary of Contents for DAP-1360















































































































































































































































































Search results

Summary of Contents for DAP-1360

Reviews:

Related manuals for DAP-1360

Brands by name

Popular brands

D-Link DAP-1360, User Manual

Search results

Summary of Contents for DAP-1360

Reviews:

Related manuals for DAP-1360

Brands by name

Popular brands