Cypress MB95710M Series Manual Download Page 67 | Manualshive

Page: 67 / 174

background image

MB95710M Series
MB95770M Series

Document Number: 002-09307 Rev. *D

Page 66 of 172

• Operation in stop mode and watch mode

• If the pin state setting bit in the standby control register (STBC:SPL) is set to “1” and the device transits to stop

mode or watch mode, the pin is compulsorily made to enter the high impedance state regardless of the DDR4 reg-
ister value. The input of that pin is locked to “L” level and blocked in order to prevent leaks due to input open.

• If the pin state setting bit is “0”, the state of the port I/O or that of the peripheral function I/O remains unchanged

and the output level is maintained.

18.5 Port 5

Port 5 is a general-purpose I/O port. This section focuses on its functions as a general-purpose I/O port. For details of
peripheral functions, refer to their respective chapters in “New 8FX MB95710M/770M Series Hardware Manual”.

18.5.1 Port 5 configuration

Port 5 is made up of the following elements.
• General-purpose I/O pins/peripheral function I/O pins
• Port 5 data register (PDR5)
• Port 5 direction register (DDR5)
• Port 5 pull-up register (PUL5)

18.5.2 Block diagrams of port 5

• P50/TO01 pin

This pin has the following peripheral function:
• 8/16-bit composite timer ch. 0 output pin (TO01)

• P51/EC0 pin

This pin has the following peripheral function:
• 8/16-bit composite timer ch. 0 clock input pin (EC0)

• P52/TI0/TO00 pin

This pin has the following peripheral functions:
• 16-bit reload timer ch. 0 input pin (TI0)
• 8/16-bit composite timer ch. 0 output pin (TO00)

• P53/TO0 pin

This pin has the following peripheral function:
• 16-bit reload timer ch. 0 output pin (TO0)

«
...
65
66
67
68
69
...
»

Summary of Contents for MB95710M Series















































































































































































Reviews:

No comments

Related manuals for MB95710M Series

Brand: Vacon Pages: 62

Brand: Samson Pages: 78

Brand: Rachio Pages: 16

Brand: EasyIO Pages: 12

Brand: RMG Pages: 6

Brand: Lattice Semiconductor Pages: 26

Brand: Easy Heat Pages: 4

Brand: Jands Pages: 7

coviva Smartbox TKP100A

Brand: hager Pages: 34

Brand: Olsberg Pages: 68

Brand: IBC Pages: 8

Brand: Linear Technology Pages: 7

J1000 CIMR-JC series

Brand: YASKAWA Pages: 25

Brand: Rain Bird Pages: 18

Brand: FASAR ELETTRONICA Pages: 2

Brand: Zander Aachen Pages: 75

Brand: Samson Pages: 44

Brand: Hansen Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands