background image

Cynko

Met

 

 

 

N-200

 

Page 48 

5.

 

Transport 

The spreader is prepared for sale in a completely assembled state and 

does  not  require  packing  unless  the  parties  have  declared  delivery  in  a 
different form. Only the machine's instruction manual is packed. 

Delivery of the spreader to the user takes place by transport on other 

machines  homologated  for  driving  on  public  roads  and  adapted  for  the 
transport of such machines. 

Loading  and  unloading  of  the  spreader  from  the  vehicle  must  be 

carried  out  using  an  unloading  ramp  by  means  of  a  drawing  vehicle 
(following the guidelines in the instruction manual concerning first start-up), 
crane or forklift. Manual towing of the mini-spreader from the vehicle onto a 
ramp  is  also  permitted.  During  operation,  observe  the  general  safety  rules 
with  handling  operations.  Persons  operating  the  reloading  equipment  must 
have the required permissions to use these devices. 

When  loading  /  unloading  using  an  all-terrain  vehicle/tractor,  the 

spreader must be properly connected with the drawing machine according to 
the requirements contained in this manual. 

When  loading  /  unloading  using  a  crane,  the  spreader  is  to  be  lifted 

with the help of approved fasteners designed to carry the load with sufficient 
capacity. The belts must be in good condition, they cannot show any signs of 
damage. 

The belts should be placed under the lower frame of the spreader in 

such places that when lifting the machine the belts do not have the possibility 
of moving, and the spreader when moving is not tilting. If there is a possibility 
of damage or frayed belts against components of the machine, put washers 
in sensitive areas. 

 

 

Summary of Contents for DZIK N-200




















































Reviews: