CURRENT Luxury SilenTrac Installation Manual Download | Manualshive

Page: 21 / 25

background image

21

Using the Remote Control- Single Drapery

Channel
Selector

LED
Indicators

66%
closed

Full
Closed

66% Open

Full open

Full Open

- A press and release moves the drapery to the full open position. A press and hold will move the drapery towards the

open position, and stop it precisely upon release.

Full Closed

- A press and release moves the drapery to the full closed position.

A press and hold will move the drapery towards the closed position, and stop it precisely upon release.

66% Open

- A press and release moves the drapery to the approximately 66% open position.

66% Closed

- A press and release moves the drapery to the approximately 66% closed position.

Channel Selector

- Successive presses and releases will change the remote channel. Current channel will be reflected on the LED

indicators.

LED Indicators

- Indicator lights for various remote functions.

«
...
19
20
21
22
23
...
»

Summary of Contents for SilenTrac


























Reviews:

No comments

Related manuals for SilenTrac

Brand: SelectBlinds Pages: 31

Brand: Velux Pages: 80

Brand: Victoria M Pages: 4

Roman Blind Safe-Release

Brand: Renaissance Pages: 4

Roller blind M cassette R76

Brand: Rollos Pages: 2

Brand: Rollos Pages: 4

Brand: Rollos Pages: 4

Brand: Erfal Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands