CURRENT Luxury SilenTrac Installation Manual Download

Page: 23 / 25

Using the Light & Temperature Sensors on the

control housing

Light Sensor
Control

Temperature
Sensor Control

Sensors Power

Light Sensor Control

- A press and release displays the current mode of the light sensor. A second press and release changes the

mode of the automated movements triggered by the light sensor.

Temperature Sensor Control

- A press and release displays the current mode of the temperature sensor. A second press and

release changes the mode of the automated movements triggered by the temperature sensor.

Sensors Power

- A press and release displays the current mode. A second press and release will change the mode of all sensor

enabled automated movements between enabled or disabled.

Light and Temperature Sensor LED Indicators

- Indicates which mode the sensor is in when the corresponding button is

pressed and released.

Sensors Power LED Indicator

- Indicates which mode the sensors are in when the corresponding button is pressed and released.

A red LED means the sensors are off. A green LED means they are on.

Light Sensor
LED Indicator

Temperature
Sensor LED
Indicator

Sensors Power
LED Indicator

Sensor Modes

The integrated light and temperature sensors have three possible modes: Off, Fully Automatic, and Semi-

Automatic.

Off

- The device will not make any movement triggered by this sensor.

Fully Automatic

- The device will open and close the curtains based on the sensor readings.

Semi-Automatic

- The device will close the curtains based on sensor readings, but will not open them.

These modes are indicated using the LEDs on the right of the control box.

- A RED light indicates the sensor is OFF

- A FLASHING GREEN light indicates the sensor is in SEMI-AUTOMATIC

- A SOLID GREEN light indicates the sensor is in FULLY AUTOMATIC

Press and release the sensor buttons to toggle through the modes.

Summary of Contents for SilenTrac


























Search results

Summary of Contents for SilenTrac

Reviews:

Related manuals for SilenTrac

Brands by name

Popular brands

CURRENT Luxury SilenTrac, Installation Manual

Search results

Summary of Contents for SilenTrac

Reviews:

Related manuals for SilenTrac

Brands by name

Popular brands