CURRENT Luxury SilenTrac Installation Manual Download Page 2

Page: 2 / 25

Drapery Track Installation

For additional help during installation of your drapery track, visit www.currentluxury.com or call 1-844-307-7435.

For proper installation of your track drapery, the following tools are required:

1/4” nut driver

5/64” hex screwdriver (spliced tracks only)

6” magnetic bit holder extension for drill

Tape measure

Drill

Level

Pencil

Ladder

7/64” drill bit for stud applications

1/4” drill bit for drywall applications with toggler anchors

#2 Phillips Screwdriver

Stud Finder (optional)

Flathead Screwdriver (optional)

Vacuum Cleaner

Safety Goggles

Track (Right draw shown)

Carriers (installed)

Carrier Arm(s)

Return Clips

Primary Motor

Secondary Motor

Pendant

Brackets

Sensor Box

Fascia

Fascia Clips

Fascia Spacers (for ceiling mount)

Track Splice

Summary of Contents for SilenTrac


























Search results

Summary of Contents for SilenTrac

Reviews:

Related manuals for SilenTrac

Brands by name

Popular brands

CURRENT Luxury SilenTrac, Installation Manual

Search results

Summary of Contents for SilenTrac

Reviews:

Related manuals for SilenTrac

Brands by name

Popular brands