CURRENT Luxury SilenTrac Installation Manual Download Page 24

Page: 24 / 25

VII. Statements

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference

that may cause undesired operation.

Warning:

Changes or modifications not expressly approved by Current Products Co. could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

RF WARNING STATEMENT

This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be

installed and operated to provide a separation distance of at least 20 cm from all persons.

Cet équipement est conforme aux limites d’exposition au rayonnement FCC / ISED établies pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé de manière à assurer une distance de séparation d’au moins 20 cm de toutes les personnes.

IC STATEMENT

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation

of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de license. L’exploitation est autorisee

aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tour brouillage

radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Summary of Contents for SilenTrac


























Search results

Summary of Contents for SilenTrac

Reviews:

Related manuals for SilenTrac

Brands by name

Popular brands

CURRENT Luxury SilenTrac, Installation Manual

Search results

Summary of Contents for SilenTrac

Reviews:

Related manuals for SilenTrac

Brands by name

Popular brands