CTC Union CTC 380 IC Installation And Maintenance Instruction Manual Download Page 16 | Manualshive

Page: 16 / 76

background image

CTC 380 IC

16

STB restore button

5. Electric installation

5.1 General information

The electric installation of the boiler must be performed by a specialist. The lines must
be laid in compliance with applicable regulations. The boiler is ready ex works for con-
nection.

5.2 Heating circuit pump

The heating circuit pump for the heating system is connected to the connection fastener
in the basic unit. The switch for the pump is on the comfort control of the
boiler.

5.3 Heating circuit mixing valve

The heating circuit mixing valve for the heating system is connected to the connection
fastener in the basic unit.

5.4 Safety temperature limiter (STB)

For extremely cold storage of the boiler, the safety temperature limiter can be
initiated. It is restored with the button at the front of the power pack.

«
...
14
15
16
17
18
...
»

Summary of Contents for CTC 380 IC













































































Reviews:

No comments

Related manuals for CTC 380 IC

Brand: A.O. Smith Pages: 48

Brand: Bakers Pride Pages: 4

Brand: Nibe Pages: 28

Brand: Alpha Pages: 44

Brand: Calomax Pages: 14

Brand: Harsco Industrial Pages: 114

Brand: Halstead Pages: 20

Resolute Boiler

Brand: ENERGY KINETICS Pages: 42

Brand: Ideal Boilers Pages: 80

Brand: Ariston Pages: 8

Brand: HRM Pages: 28

Brand: Sime Pages: 100

Brand: Climit Pages: 72

Brand: Potterton Pages: 36

Lynx Electronic

Brand: Potterton Pages: 4

Brand: Ideal Boilers Pages: 4

Brand: Gledhill Response Pages: 12

Brand: Wolf Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands