background image

GLASS  DRILL INSTRUCTION  MANUAL

PRODUCT MANUAL

crlaurence.com

C.R. Laurence Co., Inc.    

    2503 E. Vernon Ave., Los Angeles, CA 90058     

    1.800.421.6144      

    crlaurence.com

NOVEMBER 2020

P. 8

3 SPECIFICATIONS

3.1 Electrical

Input voltage .............................................................................. 115 VAC single phase
Power requirement ................................................................. Melt unit 900 W
............................................................................................................ Hose, 8 ft 262 W
............................................................................................................ Hose, 12 ft 390 W
............................................................................................................ Handgun 120 W
Breaker rating............................................................................. 15 A 

3.2 Physical

Tank capacity ............................................................................. 4.5 kg (10 lb)
Hose capacity ............................................................................ 1 no. 8 hose
Shipping weight ........................................................................ 29.1 kg (64 lb) 

3.3 Performance

Warm up time ............................................................................. 45–60 minutes
Melt rate ........................................................................................ 3.6 kg/hr (8 lb/hr)
Viscosity ........................................................................................ Maximum 500,000 cps
Temperature range:

Melt tank ................................................................................ 37–232 °C (100–450 °F)

       Hose ........................................................................................ 175–232 °C (350–450 °F)
Maximum pump flow rate:
       Motor rpm ............................................................................  38/31 rpm @ 60/50 Hz
       Pump size .............................................................................  V1-675
       Output .................................................................................... 18.1 kg/hr (40 lb/hr)

3.4 Environmental

Storage temperature ............................................................. 0–60 °C (32–140 °F)
Ambient air temperature ..................................................... 5–45 °C (41–113 °F)
Humidity ....................................................................................... 30–95 R.H. (%)

Summary of Contents for CRL SS96
































Reviews: