CRH CRL SS96 Product Manual Download Page 24

Page: 24 / 31

GLASS DRILL INSTRUCTION MANUAL

PRODUCT MANUAL

crlaurence.com

C.R. Laurence Co., Inc.

•

2503 E. Vernon Ave., Los Angeles, CA 90058

•

1.800.421.6144

•

crlaurence.com

NOVEMBER 2020

P. 24

9 PARTS LIST

9.1 SS96 Assembly Drawing

Item

Description (Quantity)

Part Number

Flow control valve assembly

73169-01

Kit, over temperature thermostat 232 °C (450 °F)

79126-450

Pump assembly, group

79048-3

Motor group

73714-24

Kit, thermometer

79014

Switch, circuit breaker, 115 VAC

12015-1

Indicator light, red

12030-1

Indicator light, amber

12030-10

Blank, switch cover

12011-3

Kit, tank controller

79006

Seal, pump shaft

70006-1

Seal, tank

70020

Capacitor, 10 µf, 370 VAC

18416-1

Lid, pan

70007

Shaft, pump

73167-2

Lid assembly

73341-1

Gun hanger

70117

Kit, tank heater 115 VAC

79005

Deflector

70213

Chain drive assembly

73164

Kit, idler gear

79094

Handle

14517-2

Scraper, chain

70213-2

Kit, pump warmup thermostat

79068-350

Cable, 16 AWG, 3 cond. 20.32 cm (8 in.) with plug, 115 VAC only (not illustrated)

12012

Summary of Contents for CRL SS96
































Search results

Summary of Contents for CRL SS96

Reviews:

Related manuals for CRL SS96

Brands by name

Popular brands

CRH CRL SS96, Product Manual

Search results

Summary of Contents for CRL SS96

Reviews:

Related manuals for CRL SS96

Brands by name

Popular brands