background image

GLASS  DRILL INSTRUCTION  MANUAL

PRODUCT MANUAL

crlaurence.com

C.R. Laurence Co., Inc.    

    2503 E. Vernon Ave., Los Angeles, CA 90058     

    1.800.421.6144      

    crlaurence.com

NOVEMBER 2020

P. 21

8 REPAIR AND REPLACEMENT (CONT.)

8.4 Pump Motor Replacement

1.  Disconnect electrical power and allow melt unit to cool to 121 °C (250 °F).
2.  Open motor junction box cover [1], disconnect wiring and liquidate fitting [2]. See illustration below.
3.  Remove screws [3] holding motor mounting plate to melt unit.
4.  Lift motor mount assembly off melt unit. Ensure pump shaft remains connected to pump in tank.
5.  Remove screws [6] holding pump motor to motor mounting plate [5].
6.  Install new pump motor on motor mounting plate.
7.  Check pump shaft alignment on pump in tank.
8.  Align motor coupling [4] with pump shaft in tank and lower onto shaft.
9.  Align motor mounting plate to melt unit with mounting screws [3].
10.  Verify pump shaft seats properly with pump and verify sufficient coupler clearance [7] exists 0.8 mm ± 0.3 mm 

(0.030 in. ±0.010 in.). See illustration below.

11.  Replace liquidate fitting and wires.
12.  Reconnect wires according to electrical schematic. Refer to melt unit identification plate to determine exact voltage.
13.  Turn melt unit on allow melt unit to heat up to normal operating temperature, turn pump motor on.
14.  Tighten screws [3] in a crisscross pattern while motor is operating to align pump shaft.

SS96 Hot Melt Unit  19600-135  Rev. B  10/26/00

23

8.4 Pump Motor Replacement

1.

Disconnect electrical power and allow melt unit to cool to
121 °C (250 °F).

2.

Open motor junction box cover [1], disconnect wiring and
liquidtite fitting [2]. See illustration below.

3.

Remove screws [3] holding motor mounting plate to melt unit.

4.

Lift motor mount assembly off melt unit. Ensure pump shaft
remains connected to pump in tank.

5.

Remove screws [6] holding pump motor to motor mounting
plate [5].

6.

Install new pump motor on motor mounting plate.

7.

Check pump shaft alignment on pump in tank.

8.

Align motor coupling [4] with pump shaft in tank and lower
onto shaft.

9.

Align motor mounting plate to melt unit with mounting
screws [3].

10. Verify pump shaft seats properly with pump and verify

sufficient coupler clearance [7] exists 0.8 mm ± 0.3 mm
(0.030 in. ±0.010 in.). See illustration below.

11. Replace liquidtite fitting and wires.
12. Reconnect wires according to electrical schematic. Refer to

melt unit identification plate to determine exact voltage.

13. Turn melt unit on allow melt unit to heat up to normal

operating temperature, turn pump motor on.

14. Tighten screws [3] in a crisscross pattern while motor is

operating to align pump shaft.

2

3

7

5

6

1

3

4

2000349

Summary of Contents for CRL SS96
































Reviews: