background image

GLASS  DRILL INSTRUCTION  MANUAL

PRODUCT MANUAL

crlaurence.com

C.R. Laurence Co., Inc.    

    2503 E. Vernon Ave., Los Angeles, CA 90058     

    1.800.421.6144      

    crlaurence.com

NOVEMBER 2020

P. 9

3 SPECIFICATIONS (CONT.)

3.5 Dimension

4 INSTALLATION

4.1 Setup

1.  Remove all packaging material around melt unit.
2.  Carefully lift melt unit out of box.
3.  Unpack binder containing manuals and warranty information. Retain for future reference.
4.  Unscrew four screws from plywood board base.
5.  Carefully uncoil hose from around melt unit and remove bubble wrap from handgun.
6.  Position melt unit for convenient servicing and easy access to control panel.
7.  Use level mounting surface to prevent warping of melt unit and misalignment of pump and motor shaft.
8.  Using the base mounting holes, bolt melt unit to a durable mounting surface in accordance with illustration on  

opposite page to prevent accidental upset and possible injury.

9.  Assure all screws are tight before startup. If melt unit experiences excessive vibration, re-tighten screws. 

4.2 Component Installation

1.  Manual systems are generally shipped with all standard components installed. No user installation is required.
2.  In the event a melt unit is received without an attached handgun/hose assembly, refer to Section 8.1, Hose Replacement.

6

SS96 Hot Melt Unit  19600-135  Rev. B  10/26/00

3.5 Dimensions

®

269.875mm 

10.625 in.

355.60mm 

14.0 in.

558.80mm

22.0 in.

285.75mm

11.25 in.

292.10mm

11.50 in.

342.90mm

13.50 in.

2000355

Summary of Contents for CRL SS96
































Reviews: