Crestron Green Light GL-IPAC-SW8 Product Manual Download Page 12 | Manualshive

Page: 12 / 45

background image

Product Manual — Doc. 7389C

GL-IPAC-SW8 • 12

③

BACK: Press button to go back to the previous screen while in Setup mode.

④

CANCEL: Press button to cancel the current operation while in Setup mode.

⑤

HELP: Press button to display the help dialog while in Setup mode. The help dialog provides
information for the screen that is currently displayed.

⑥

ENTER: Press button to confirm the current on-screen selection.

⑦

Four Soft Buttons: For making selections based on the display options shown above the
buttons.

⑧

PWR LED: Illuminates to show that the device is powered.

⑨

NET LED: Illuminates to show activity on the Cresnet network.

⑩

MSG LED: Illuminates to show that the processor has generated an error message.

⑪

HW-R: Press button for hardware reset.

⑫

SW-R: Press button for software reset.

⑬

OVR: Press button to enter override mode. LED illuminates to indicate override mode.

Wiring Diagram

The following illustration is a detailed connection overview of a GL-IPAC-SW8 system.

«
...
10
11
12
13
14
...
»

Summary of Contents for Green Light GL-IPAC-SW8














































Reviews:

No comments

Related manuals for Green Light GL-IPAC-SW8

Brand: S&C Pages: 40

Brand: Lattice Semiconductor Pages: 30

Brand: WAFER Pages: 15

Brand: Vasco Pages: 32

Brand: Abra Pages: 16

Brand: SAI Pages: 16

Brand: Hable Pages: 3

Brand: EasyIO Pages: 18

Brand: Easylift Pages: 127

Brand: Feig Electronic Pages: 153

Brand: Galaxy Control Systems Pages: 5

Brand: Harsco Industrial Pages: 57

Brand: Harmar Mobility Pages: 53

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

Brand: RAKwireless Pages: 6

Brand: Fingertips Lab Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands